Just finally finished this 5 litre ribbon blender with full vacuum rating as well as a heating jacket complete with thermostat controlled heating elements all set up to be on castors for a mobile solution.
Just finished 2 very smart looking tanks / IBC's set up for line marking paint. All radiused corners and a bag filter cage.
Progress photos of a 5 litre ribbon blender with full vacuum rating as well as a heating jacket complete with thermostat controlled heating elements all set up to be on castors for a mobile solution.
Just completed another steam injected rotating cooker for a food application for a multinational food company.
The pharma customer needed a magnetic drive mixer to be installed in their small 32 litre dosing tank.
While we are pretty proud of this 6 compartment coffee bean hopper, its not only about the fabrication, but also the installation knowledge and skills developed over many years.
A customer needed a special shaped rectangular tank for a specific requirement.
A multinational chemical company needed a replacement tank, so details had to be closed so as to lift out and lift in the new one - the pipework connections on the new tank matched the old chemical.
This tank is to replace an existing tank, which will be lifted in through the roof and therefore the ladder and platform need to be easily removeable and reinstalled.
STOCK 316 grade 500 LITRE JACKETED PRESSURE/VACUUM CONTRAMIX TANK
Just finished a very neat mix station with jacketed [for heating] mix tank.
In house pre-polishing of a pressure vessel and then being plastic covered to protect the surface while fabricating.
Both mixers have a spare bowl, so one can be getting washed while the other is operating. The bowls are easily removed and replaced with a simple clamp at the back.
We had an urgent call out this week to fix a leaking 250,000 litre silo. Now a food grade silo this big is an expensive bit of equipment, but unfortunately they are simply and easily catastrophically damaged.
A 25,000 litre heated, insulated & clad and agitated storage tank, heated with heat trace ready to be transported to site.
24 off mobile pressure / vacuum transfer vessels for the food industry.
A 2000-liter ribbon blender is still going strong, the only maintenance it has probably had changes to the gland packing on the shaft seals.
2 off jacketed contra-mix tanks fabricated from SAF2205 - a duplex stainless steel for a corrosive environment and fitted to a full stainless steel platform
These photos are of 1/2 a platform under construction. All chequer plate flooring is fully sealed welded and folded at the edges to create a very clean arrangement.
Australian-made custom stainless steel solutions got a small ETFE-lined vessel for chemical recovery at a demonstration facility.
Just another day in the office - some 3mm transition hoppers with sight glasses, specific baffle and nozzles
Our recent development of a 200 litre blender to add to our stingray range
While there may be common sizes, very often those sizes don't work because of site constraints, whether it be the width or the height, or the clearance under the tank.
24 off mobile pressure/vacuum for transporting/storing/dispensing viscous semi-liquid food products in the process of being built for a reputable Australian Food manufacturer.
The customers shear mixing head had been repaired/refurbished a number of times until finally needed replacing. Contact us for a bespoke system to suit your specific needs
This laboratory bench includes 2 off lexan faced PC monitor locations.
Just finished this mixing tank which is insulated and clad with seal welded cladding, having a scrape surface cage type mixer and CIP spray ball setup. All are built to exacting GMP and safety standards.
Nothing special about these tanks except the customer who is using these tanks as part of a larger project commented.
The 50 litre tank has a heat trace system fitted for heating the tank - completely enclosed in a seal welded jacket and a tidy junction box.
This tumble type blender [best described as a concrete mixer, except this it isn't for concrete, but rather for food and similar products] has a working capacity of 200 litres / 200 kgs.
Nothing very exciting, but you can be sure these vats will be still operational after 100 years.
Large ductwork needs the right design, material, gauge, adaptors, and fittings to perform well in industrial and large manufacturing environments.
IBC's [Intermediate Bulk Containers] play an important part in increasing efficiency in the production facility.
A very tidy mobile EX-rated mix tank complete with load cells for batching as well as dispensing with accuracy.
This blender was built after conducting tests in our pilot scale blender to determine the best method of mixing the customers ingredients.
Had to pay a site visit this week to suggest what could be done for this bag filter vessel.
A rush job to help out a valued customer delivered in the promised timeframe.
A customer required a lab blender to blender to do product trials in their lab with details to be scaled down from their production equipment.
Not really sure what is it! But it looks good! All were built from scratch in our Minto workshop.
Focusing on the production of Ribbon blenders for the months of May and June 2022
High polished storage tanks to make it easier for the customer's product to be cleaned off.
Not the greatest photos, but another quality ribbon blender complete with: * associated platform, * painted support structure - made separate so as to be able to install the blender inside an existing room * included is a vacuum lifting system for the operator to load the mixer with bags * 3 alternative size screens complete with safety switch tongue * upper and lower level controls for ease of operating.
Our mix stations are a highly flexible piece of equipment especially when speeding up the process of pre-blending that includes blending powder into liquid.
